Product Description
What are the symptoms of a damaged half shaft?
The half shaft is the component that transmits power to the wheels. Without the half shaft, the power cannot be transmitted to the wheels. If the car’s half shaft is damaged, it will cause the car to vibrate abnormally when driving, and will also cause abnormal noises when the car is driving. If the drive shaft is damaged, it needs to be replaced immediately.
If there is a problem with the drive shaft when the vehicle is driving at high speed, it may cause the car tires to fall off or the wheel hub to become out of round. The wheel hub out of roundness will cause the car’s dynamic balance to become unbalanced, causing the car’s high-speed steering wheel to shake. In the vehicle’s transmission system, the half shaft plays an important role and is the shaft that connects the drive wheels and the differential. The inner tie rod ends are generally connected to each other through side gears and splines, and the outer tie rod ends are connected to the wheel hub and flange. The structure of the automobile drive wheel is determined by the structural form of the half shaft. According to the different stress conditions of the half shaft, it can be divided into semi-floating half shaft and fully floating half shaft. It can be seen that the automobile half shaft is the most important factor in the daily driving of the car. An important component, the safe driving of the car depends on the performance of the drive shaft. After long-term torsional fatigue and impact, automobile half shafts are prone to bending, breakage, twisting, skewing, and spline tooth wear. The fractures of automobile half shafts usually have the following morphological types: 1.The spiral of the half-shaft shaft is broken; 2. Mixed cracks and fractures appear in the half-shaft shaft; 3.The splines of the half-shaft are broken; 4.The half-shaft is blue Cracks appear on the disc, and may even fall off in severe cases; 5.Other morphological fractures and cracks in the half shaft.
Product description
HDAG oem -20 2-1 auto spare parts propeller half shaft cardan rear axle reinforced drive shaft for chevrolet niva vaz 2123 2121-21214
Item Name | Auto or car CV JOINT,Universal Joint,CV JOINT INNER OUTER, DRIVE SHAFT, DRIVESHAFT,CV AXLE, JOINT SHAFT ASSEMBLY,CV AXLE JOINT SHAFT, HALF SHAFT, WHEEL BEARING HUB, WHEEL HUB BEARING, WHEEL BEARING | |||||||||||||||||||
OEM/REF NO. | 2 2 2 2 2 2 2 -20 21213 -2203012-1 | |||||||||||||||||||
Car Model | For lada UAZ 2206/3151/3303/3741/9 3741 236571 3160 3163 NIVA VAZ samara moskvich 2141 Tavria 1102 GRANTA LARGUS Vesta X-Ray Kalina PRIORA BA3 Granta Kalina Priora OKA VESTA Gazelle Gazelle Gazel Gazon Kamaz Patriot | |||||||||||||||||||
POSITION | RH/LH/Right/ Left/ Front/Rear | |||||||||||||||||||
MOQ | 150PCS | |||||||||||||||||||
Quality/Product parameters | OEM standard or Design as sample or drawing | |||||||||||||||||||
Payment Terms | T/T, L/C, Credit card, Cash | |||||||||||||||||||
Product Guarantee | 1 Year or 50, TOYOTA : TOYOTA : TOYOTA : 4342 TOYOTA : 4342 TOYOTA : 4342R20 TOYOTA : 4346R30 TOYOTA : 4346S50 TOYOTA : 4346 TOYOTA : 4347S60 TOYOTA : 4347U90 TOYOTA : TOYOTA : TOYOTA : 434708Z033 TOYOTA : 434708Z037 |
NISSAN : 391J10 NISSAN : 391571JJ10 NISSAN : 39157117JJ10 NISSAN : 3910110JJ10 |
NISSAN : 391M615 NISSAN : 391Y10 NISSAN : 391M570 NISSAN : 391N215 NISSAN : 391571M311 NISSAN : 391571M915 NISSAN : 3910140Y10 NISSAN : 391014M570 NISSAN : 391014M575 NISSAN : 391014M771 NISSAN : 3910163Y10 NISSAN : 391016N215 |
MAZDA : G057155J210 NISSAN : 391J171 NISSAN : 391N275 NISSAN : 391J071 NISSAN : 391J915 NISSAN : 391E478 NISSAN : 391012J215 NISSAN : 391014N175 NISSAN : 391014N177 NISSAN : 391014N275 NISSAN : 391015J571 NISSAN : 391016J571 NISSAN : 391016J071 NISSAN : 391016J076 NISSAN : 391016J915 NISSAN : 39101AE415 NISSAN : 39101AU415 NISSAN : 39101AU416 NISSAN : 39101AW110 NISSAN : 39101CX116 NISSAN : 39101WF715 NISSAN : 39101WF716 |
391 | 391M10 TOYOTA : 4347Z035 TOYOTA : 434708Z039 |
374077/374078/374092/7837456/7839615/7837457 | 3920164Y10 | G564-25-5, 8D0498103, 8D0498103A,3B0498103,43145711H | 8D0498099A,8D 0571 15H,8D0498099C,8D 0571 15H | 43420-20380 | 3748103A | 86~88099 | 435711011 | 44105-78B VAG : |
6Q0498099E, 6Q0498099B, 6Q0498099EX | 43403-6, 96564144 ,96396134,512395 |
39211-3U | 39211-BM726 | FD50-25-40XA, FA60-25-40X, FA58-25-50X FA252560XA/FA557160X/FA5822510/FA5822510B/FD54-25-60XA/FD55-25-50XA |
1K0498103C | 8K0498099X,8K0498099,8K0498099D | 17145711 171498UU507 NISSAN : 391V70A NISSAN : 391013U505 NISSAN : 391014V01C NISSAN : 391014V51A NISSAN : 391014V70A NISSAN : 392113U 96348790 |
391 VOLVO : 8111304 VOLVO : 86011 VOLVO : 9122833 VOLVO : 9163595 |
7L 0571 11D,95534995712,95534995710, 7L0498099CX,7L0498099AX | 17145711J,171498099A | 374403/374403/9201725 | 39211-7F | 8K 0571 15C, 8K0498099B, 8K0498099BX | 171498099B,171498099BX | 96273760/96549104/96951692 | 392112F225 | MAZDA : G5712510 MAZDA : G571550X MAZDA : G571560X MAZDA : G565715 OPEL : 374 VAUXHALL : 571 |
391 MAZDA : MD1922510 MAZDA : MD1922510A MAZDA : MD192550X MAZDA : MD257160XB |
|||||||
44014-SP0- OPEL : 374048 OPEL : 374067 OPEL : 37408 OPEL : 374118 OPEL : 374148 OPEL : 374195 OPEL : 90125876 OPEL : 90157212 OPEL : 95718734 OPEL : 9317340 OPEL : 93173430 SAAB : 4242319 |
392114F425 | MD20-25-60X | ||||||||||||||||||
44305SE0J22/44306SE0G12/44305SE0G23/44305SE0G24/44305SE0J20 | A6383342334 | 391KD0A NISSAN : 391KD0A NISSAN : 391019Y015 NISSAN : 39101CNY015 NISSAN : 39211CNHN50 HONDA : 44305S04J60 HONDA : 44305S0A960 HONDA : 44305S0AN60 HONDA : 44305S2H571 HONDA : 44305S2H050 HONDA : 44305S2H950 HONDA : 44305S2H951 HONDA : 44305S2HN50 HONDA : 44305S5AJ50 HONDA : 44305S5AJ60 HONDA : 44305S5AJ61 HONDA : 44305S5AJ62 HONDA : 44305S5C950 HONDA : 44305S5CN50 HONDA : 44305S5CN51 HONDA : 44305S7B950 HONDA : 44305S7C950 HONDA : 44305SOA960 HONDA : 44305SOAN60 HONDA : 44306S0A960 HONDA : 44306S0AN60 HONDA : 44306S2H571 HONDA : 44306S2H950 HONDA : 44306S2H951 HONDA : 44306S5AJ51 HONDA : 44306S5AJ61 HONDA : 44306S5AJ62 HONDA : 44306S5C951 HONDA : 44306S5C952 HONDA : 44306S7B950 HONDA : 44306S7C950 HONDA : 44306SOA960 HONDA : 44306SOAN60 |
49591-1F410 | 44305-SA5-000,44305-688-000,44306-689-601,44306-688-571,44305-688-571 | 4401720,4401727,8200169277,8200169281,8200169285,8200169288,8200196277,8200178624 | 39210-Y02G0 326582 |
FG02-25-500D FG02-25-500E FG02-25-600D FG02-25-600E |
|||||||||||||
44014-SDC-A50,44014-SCA-E01,44014SDCA51, | 9565719/3273.17/3273.18/3273.20/3273.21/3273.23/3273.24/3274.79/3274.80 | 44305-SB2-750,44305-SF4-J21,44306-SK7-571 44305-SA2-960 |
825716110,7700111918,8200064731, | 39100ED005 39100ED00A 39101ED00A 39101ED005 |
GF09-25-50X,GP28-25-50XA/GD36-25-60X | |||||||||||||||
44014-SWE-T00,44014-SWE-T01,44014-SWA-000,44014-SWA-571,44014-SXS-A00 | 3272.00/3272.20/3273.55/3273.64/95598120 | 44305-SB2-982,44306-SB0-571 44571-SH3-J01,44306-SB2-984 |
7701351572,7701351571,7701351484,7701351480,7701351479,7701349938,7701349880,7701349874 |
39100-JX00A 39211-CN000 |
GP34-25-60XD | |||||||||||||||
44014-SDE-T00,44014SDCA00,44306SDETOOL | 3272.06/3273.75 | 44305-SH3-961, 44306-SH3-571, 44305-SE0-000,44571-SH3-960,44011-SH3-G12,44305-SH3-961 | 8200264664,39100-0153R,39101-5451R,6001548720,8200690053,820571122 | 1N00-25-500 | KIA : 0K558-25-50X KIA : 0K558-25-60X |
|||||||||||||||
44305-TL1-E00,44014TA0A00 | 3273.Y7 3272.S5 |
44571SL5N01 44571SS571 44571SS0030 44011SS571 44011SS0030 | 391014946R | 39100-AX000 39211-AY125 39101-AX005 39100-AX005 39101-AX000 |
MAZDA : M 0571 1510 MAZDA : M 0571 1510A MAZDA : M 0571 1500C MAZDA : M 0571 1500D MAZDA : M 0571 1600A MAZDA : M 0571 1600B MAZDA : MD0925500A MAZDA : MD0925600A |
|||||||||||||||
44014-S9A-571,44014-SDC-A50,44014-S9A-571, 44014-SCA-E00,44014-SCA-E01 | 3273.60/3273.62/3273.C7/3274.77/95606802/95646292/96184033 | 44305-SM4-983, 44571-SM4-A01, 44571-SL5-N01,44571-SV4-951,44011-SS0-930, | 77,013,524,157,701,300,000 | 39210-F4125 | MAZDA : G064-25-500 MAZDA : G064-25-600 MAZDA : G564-25-500A MAZDA : G564-25-600A MAZDA : G564-25-60X MAZDA : GR01-25-500 MAZDA : GR01-25-50X MAZDA : GR01-25-600 MAZDA : GR01-25-60X MAZDA : GU01-25-500 MAZDA : GU01-25-50XA MAZDA : GU01-25-50XC MAZDA : GU01-25-600 MAZDA : GU01-25-60XA MAZDA : GU01-25-60XD |
|||||||||||||||
44305-SAA-E00 | 9566722380/1495545080/1496138080/9567582280 | 44571-S07-000,44571SR3J01,44571SR3J02 | 299341X2 | 39100-1KA5B | GG06-25-50XC | |||||||||||||||
HONDA : 44014-SDC-A00 HONDA : 44014-SNG-000 HONDA : 44305-SDC-A00 HONDA : 44305-SEA-000 HONDA : 44305-SNG-571 HONDA : 44306-SDC-A01 HONDA : 44306-SDE-T00 HONDA : 44306-SEA-000 HONDA : 44306-SNG-571 |
1495537080;1495541080;9566722180,9566722180 | 44571SR3J03/44571SR3J53/44571ST7N00/44011S07000/44305SF1G10/44011ST3E00/44571-S07-950/44571-ST3-E50 | 9109186,775712978,775712980,775712998,775712999
|
NISSAN : 39100JA571 NISSAN : 39100JD24B NISSAN : 39100JD52B NISSAN : 39101JD24B NISSAN : 39101JD52B NISSAN : 39211JA00A NISSAN : 39211JD22B NISSAN : C9211JA00A NISSAN : C9211JD22B NISSAN : C92AAJA00A NISSAN : C92AAJD22B NISSAN : C9B11JA00A NISSAN : C9BAAJA00A |
MAZDA : CTA125500 MAZDA : FA8571500A MAZDA : FA8571600B MAZDA : FA8125600B MAZDA : FA8225500A MAZDA : FD8571500B MAZDA : FD8571600A MAZDA : FP0125500C |
|||||||||||||||
44014-SDC-A00,44014-SDC-A00,44014-SDE-T00,44014-SNG-000,44306-SNG-571 | 3272-EX 3272-HY 3272-KW 3273-HQ 3273-KJ |
43460-49125/43460-49165/43460-49315/43470-80013/43470-39545 | 1991909 | NISSAN : 39100-ED100 NISSAN : 39100-ED105 NISSAN : 39100-ED305 NISSAN : 39100-ED805 NISSAN : 39101-ED105 NISSAN : 39101-ED305 NISSAN : 39101-ED805 NISSAN : 39211-ED100 NISSAN : C9211-EL10A |
KIA : 0K2N122520 KIA : KK38825600 |
|||||||||||||||
44014-S6D-E01 | 3272.3C | 43410-12500,43410-57180 | TDJ10571 | 39100-AX000/39100-ED100 | HYUNDAI : 49500-25301 HYUNDAI : 49500-25302 HYUNDAI : 49500-25310 HYUNDAI : 49500-25311 HYUNDAI : 49500-25312 KIA : 49500-25301 KIA : 49500-25302 KIA : 49500-25310 KIA : 49500-25311 KIA : 49500-25312 |
|||||||||||||||
44014-TA0-A00,44305-TA0-J00,44305-TA2-J00,44305-TL1-E00,44305-TL3-000,44306-TA0-J00 | 1481451080/3272.9C/3273.3Q | 43460-19795 | LAND ROVER : RTC6811 LAND ROVER : STC3046 |
4571-M7226 40011-M5626 39100-M7270 39101-M7270 39113-M7275 39112-M7225 |
4950624A00/MB297343/MB297873/MB526582/MB176160/MB176161/MB176865 | |||||||||||||||
44014-S9A-571,44014-SDE-T51, 44014-SMT-G01,44306-SEA-N00,44306S9AN00 | 9619947580 | 43410-57120/43460-19865/43420-12430 | LAND ROVER : STC3051 LAND ROVER : TDJ00571 |
39101-1HS0A | HYUNDAI : 49500-25200 HYUNDAI : 49500-25400 KIA : 49500-25200 KIA : 49500-25400 |
|||||||||||||||
44306-SAA-000,44306-SFA-000,44306-SFB-000,44305-SAA-000 | 9619947580/9619947588/9619947688/9619947680 | 43410-12610, 43410-57130, 43410-12520,43410-0W270 | LAND ROVER : LR060382 LAND ROVER : TDB500110 LAND ROVER : TDJ500030 |
39100CA000 39101-CA100 39211-CA100 39100-CA100 |
49508-22A00 49508-22E00 | |||||||||||||||
44014SD5A51 | 9619947580/9619947588/9619947688/9619947680 | 43430-0K571/43430-0K030/43460-80033 | HONDA : 44305S74E00 HONDA : 44305S74E01 HONDA : 44305S74E51 ROVER : GCV1123 ROVER : TFB000070 |
39100-AX000 39211-AY125 39101-AX005 39100-AX005 39101-AX000 |
MB176872, MB297376, MB297377,MB526456,49500-2D002 | |||||||||||||||
44014-S91-571,44014S9A571,44305S9AN00,44305SCAG00 | CITROEN : 3272QF CITROEN : 3272TH CITROEN : 3272WX CITROEN : 3273QQ CITROEN : 3273TT CITROEN : 3273XR DS : 3272QF DS : 3272TH DS : 3273QQ DS : 3273TT PEUGEOT : 3272QF PEUGEOT : 3272TH PEUGEOT : 3272WX PEUGEOT : 3273QQ PEUGEOT : 3273TT PEUGEOT : 3273XR |
43420-5710/43470-5711/43430-5711 | GCV1194,TDJ100590 | 39211-CG000 39211-CG571 |
MB297438,MB297678,MB526831,MB297696,MB526473 |
/* March 10, 2571 17:59:20 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
After-sales Service: | Three Years |
---|---|
Condition: | New |
Color: | OEM Standard |
Certification: | CE, ISO, ISO/Ts16949 |
Type: | C.V. Joint |
Application Brand: | Nissan, Iveco, Toyota, Ford, Lada Mitsubishi FIAT Opel Peugeot Renault Citroen |
Customization: |
Available
| Customized Request |
---|
Can cardan shafts be adapted for use in both automotive and industrial settings?
Yes, cardan shafts can be adapted for use in both automotive and industrial settings. They are versatile components that offer efficient power transmission and can be customized to meet the specific requirements of various applications. Let’s explore how cardan shafts can be adapted for both automotive and industrial settings:
1. Automotive Applications:
– Cardan shafts have long been used in automotive applications, especially in vehicles with rear-wheel drive or all-wheel drive systems. They are commonly found in cars, trucks, SUVs, and commercial vehicles. In the automotive sector, cardan shafts are primarily used to transmit torque from the engine or transmission to the differential or axle, allowing power to be distributed to the wheels. They provide a reliable and efficient means of transferring power, even in vehicles that experience varying loads, vibration, and misalignment. Cardan shafts in automotive applications are typically designed to handle specific torque and speed requirements, taking into account factors such as vehicle weight, horsepower, and intended use.
2. Industrial Applications:
– Cardan shafts are also widely used in various industrial settings where torque needs to be transmitted between two rotating components. They are employed in a diverse range of industries, including manufacturing, mining, agriculture, construction, and more. In industrial applications, cardan shafts are utilized in machinery, equipment, and systems that require efficient power transmission over long distances or in situations where angular misalignment is present. Industrial cardan shafts can be customized to accommodate specific torque, speed, and misalignment requirements, considering factors such as the load, rotational speed, operating conditions, and space constraints. They are commonly used in applications such as conveyors, pumps, generators, mixers, crushers, and other industrial machinery.
3. Customization and Adaptability:
– Cardan shafts can be adapted for various automotive and industrial applications through customization. Manufacturers offer a range of cardan shaft options with different lengths, sizes, torque capacities, and speed ratings to suit specific requirements. Universal joints, slip yokes, telescopic sections, and other components can be selected or designed to meet the demands of different settings. Additionally, cardan shafts can be made from different materials, such as steel or aluminum alloy, depending on the application’s needs for strength, durability, or weight reduction. By collaborating with cardan shaft manufacturers and suppliers, automotive and industrial engineers can adapt these components to their specific settings, ensuring optimal performance and reliability.
4. Consideration of Application-Specific Factors:
– When adapting cardan shafts for automotive or industrial settings, it is crucial to consider application-specific factors. These factors may include torque requirements, speed limits, operating conditions (temperature, humidity, etc.), space limitations, and the need for maintenance and serviceability. By carefully evaluating these factors and collaborating with experts, engineers can select or design cardan shafts that meet the unique demands of the automotive or industrial application.
In summary, cardan shafts can be adapted and customized for use in both automotive and industrial settings. Their versatility, efficient power transmission capabilities, and ability to accommodate misalignment make them suitable for a wide range of applications. By considering the specific requirements and collaborating with cardan shaft manufacturers, engineers can ensure that these components provide reliable and efficient power transfer in automotive and industrial systems.
Can cardan shafts be customized for specific vehicle or equipment requirements?
Yes, cardan shafts can be customized to meet the specific requirements of different vehicles or equipment. Manufacturers offer a range of customization options to ensure that the cardan shafts are tailored to the unique needs of each application. Let’s explore how cardan shafts can be customized:
1. Length and Size:
– Cardan shafts can be manufactured in various lengths and sizes to accommodate the specific dimensions of the vehicle or equipment. Manufacturers can customize the overall length of the shaft to ensure proper alignment between the driving and driven components. Additionally, the size of the shaft, including the diameter and wall thickness, can be adjusted to meet the torque and load requirements of the application.
2. Torque Capacity:
– The torque capacity of the cardan shaft can be customized based on the power requirements of the vehicle or equipment. Manufacturers can design and manufacture the shaft with appropriate materials, dimensions, and reinforcement to ensure that it can transmit the required torque without failure or excessive deflection. Customizing the torque capacity of the shaft ensures optimal performance and reliability.
3. Connection Methods:
– Cardan shafts can be customized to accommodate different connection methods based on the specific requirements of the vehicle or equipment. Manufacturers offer various types of flanges, splines, and other connection options to ensure compatibility with the existing drivetrain components. Customizing the connection methods allows for seamless integration of the cardan shaft into the system.
4. Material Selection:
– Cardan shafts can be manufactured using different materials to suit the specific application requirements. Manufacturers consider factors such as strength, weight, corrosion resistance, and cost when selecting the material for the shaft. Common materials used for cardan shafts include steel alloys, stainless steel, and aluminum. By customizing the material selection, manufacturers can optimize the performance and durability of the shaft.
5. Balancing and Vibration Control:
– Cardan shafts can be customized with balancing techniques to minimize vibration and ensure smooth operation. Manufacturers employ dynamic balancing processes to reduce vibration caused by uneven distribution of mass. Customized balancing ensures that the shaft operates efficiently and minimizes stress on other components.
6. Protective Coatings and Finishes:
– Cardan shafts can be customized with protective coatings and finishes to enhance their resistance to corrosion, wear, and environmental factors. Manufacturers can apply coatings such as zinc plating, powder coating, or specialized coatings to prolong the lifespan of the shaft and ensure its performance in challenging operating conditions.
7. Collaboration with Manufacturers:
– Manufacturers actively engage in collaboration with customers to understand their specific vehicle or equipment requirements. They provide technical support and expertise to customize the cardan shaft accordingly. By collaborating closely with manufacturers, customers can ensure that the cardan shaft is designed and manufactured to meet their precise needs.
Overall, cardan shafts can be customized for specific vehicle or equipment requirements in terms of length, size, torque capacity, connection methods, material selection, balancing, protective coatings, and finishes. By leveraging customization options and working closely with manufacturers, engineers can obtain cardan shafts that are precisely tailored to the application’s needs, ensuring optimal performance, efficiency, and compatibility.
Which industries and vehicles commonly use cardan shafts for power distribution?
Cardan shafts, also known as propeller shafts or drive shafts, are widely used in various industries and vehicles for efficient power distribution. Their versatility and ability to transmit torque between non-aligned components make them essential in numerous applications. Here are some of the industries and vehicles that commonly utilize cardan shafts:
1. Automotive Industry:
– Cardan shafts have extensive use in the automotive industry. They are found in passenger cars, commercial vehicles, trucks, buses, and off-road vehicles. In these vehicles, cardan shafts transmit torque from the gearbox or transmission to the differential, which then distributes the power to the wheels. This allows the wheels to rotate and propel the vehicle forward. Cardan shafts in the automotive industry are designed to handle high torque loads and provide smooth power delivery, contributing to the overall performance and drivability of the vehicles.
2. Agriculture and Farming:
– The agriculture and farming sector extensively relies on cardan shafts for power distribution. They are commonly used in tractors and other agricultural machinery to transfer power from the engine to various implements and attachments, such as mowers, balers, tillers, and harvesters. Cardan shafts in agricultural applications enable efficient power delivery to the implements, allowing farmers to perform tasks like cutting crops, baling hay, tilling soil, and harvesting with ease and productivity.
3. Construction and Mining:
– The construction and mining industries utilize cardan shafts in a wide range of machinery and equipment. Excavators, loaders, bulldozers, and crushers are examples of machinery that employ cardan shafts to transmit power to different components. In these applications, cardan shafts ensure efficient power distribution from the engine or motor to the drivetrain or specific attachments, enabling the machinery to perform tasks like digging, material handling, and crushing with the required power and precision.
4. Industrial Equipment and Machinery:
– Various industrial equipment and machinery rely on cardan shafts for power transmission. They are used in pumps, compressors, generators, conveyors, mixers, and other industrial machines. Cardan shafts in industrial applications transmit rotational power from the motor or engine to the driven components, enabling the machinery to perform their specific functions. The flexibility and misalignment compensation provided by cardan shafts are particularly valuable in industrial settings where the power source and driven components may not be perfectly aligned.
5. Marine and Shipbuilding:
– The marine and shipbuilding industry also utilizes cardan shafts for power distribution. They are commonly found in propulsion systems of boats and ships. Cardan shafts in marine applications connect the engine or motor to the propeller, ensuring efficient transmission of rotational power and enabling the vessel to navigate through water. The ability of cardan shafts to compensate for misalignment and accommodate variations in the shaft angle is crucial in marine applications, where the propeller shaft may not be in a direct alignment with the engine.
6. Rail and Locomotives:
– Rail and locomotive systems employ cardan shafts for power distribution. They are crucial components in the drivetrain of locomotives and trains, enabling the transmission of torque from the engine or motor to the wheels or axles. Cardan shafts in rail applications ensure efficient power delivery, allowing locomotives and trains to transport passengers and goods with the required speed and traction.
In summary, cardan shafts are widely used in various industries and vehicles for power distribution. They are commonly found in the automotive industry, agriculture and farming, construction and mining machinery, industrial equipment, marine and shipbuilding applications, as well as rail and locomotive systems. The versatility, flexibility, and efficient power transmission provided by cardan shafts make them indispensable components in these industries and vehicles, contributing to their performance, productivity, and reliability.
editor by CX 2024-02-22
China Standard CV Half Axle Drive Shaft Assembly Half Shaft for CZPT Pajero V95 V93 V97 manufacturer
Product Description
Why Choose Us
1.Reply your enquiry in 24 working hours,any time you can contact me.
2.OEM, buyer design, buyer label services provided.
3.Exclusive and unique solution can be provide to our customer by our welltrained
and professional engineers and staffs.
4.we have the certification of ISO 9001
5.Special discount and protection of sales area provided to our distributor.
6.timely delivery
7.Good after-sale service
8.Small MOQ is acceptable
Condition: | New |
---|---|
Axle Number: | 2 |
Application: | Car |
Certification: | ASTM |
Material: | Iron |
Type: | Rear Axles |
Customization: |
Available
| Customized Request |
---|
What is a driveshaft and how much does it cost to replace one?
Your vehicle is made up of many moving parts. Knowing each part is important because a damaged driveshaft can seriously damage other parts of the car. You may not know how important your driveshaft is, but it’s important to know if you want to fix your car. In this article, we’ll discuss what a driveshaft is, what its symptoms are, and how much it costs to replace a driveshaft.
Repair damaged driveshafts
A damaged driveshaft does not allow you to turn the wheels freely. It also exposes your vehicle to higher repair costs due to damaged driveshafts. If the drive shaft breaks while the car is in motion, it may cause a crash. Also, it can significantly affect the performance of the car. If you don’t fix the problem right away, you could risk more expensive repairs. If you suspect that the drive shaft is damaged, do the following.
First, make sure the drive shaft is protected from dust, moisture, and dust. A proper driveshaft cover will prevent grease from accumulating in the driveshaft, reducing the chance of further damage. The grease will also cushion the metal-to-metal contact in the constant velocity joints. For example, hitting a soft material is better than hitting a metal wall. A damaged prop shaft can not only cause difficult cornering, but it can also cause the vehicle to vibrate, which can further damage the rest of the drivetrain.
If the driveshaft is damaged, you can choose to fix it yourself or take it to a mechanic. Typically, driveshaft repairs cost around $200 to $300. Parts and labor may vary based on your vehicle type and type of repair. These parts can cost up to $600. However, if you don’t have a mechanical background, it’s better to leave it to a professional.
If you notice that one of the two drive shafts is worn, it’s time to repair it. Worn bushings and bearings can cause the drive shaft to vibrate unnecessarily, causing it to break and cause further damage. You can also check the center bearing if there is any play in the bearing. If these symptoms occur, it is best to take your car to a mechanic as soon as possible.
Learn about U-joints
While most vehicles have at least one type of U-joint, there are other types available. CV joints (also known as hot rod joints) are used in a variety of applications. The minor axis is shorter than the major axis on which the U-joint is located. In both cases, the U-joints are lubricated at the factory. During servicing, the drive shaft slip joint should be lubricated.
There are two main styles of U-joints, including forged and press fit. They are usually held in place by C-clamps. Some of these U-joints have knurls or grooves. When selecting the correct fitting, be sure to measure the entire fitting. To make sure you get the correct size, you can use the size chart or check the manual for your specific model.
In addition to lubrication, the condition of the U-joint should be checked regularly. Lubricate them regularly to avoid premature failure. If you hear a clicking sound when shifting gears, the u-joint space may be misaligned. In this case, the bearing may need to be serviced. If there is insufficient grease in the bearings, the universal joint may need to be replaced.
U-joint is an important part of the automobile transmission shaft. Without them, your car would have no wheeled suspension. Without them, your vehicle will have a rickety front end and a wobbly rear end. Because cars can’t drive on ultra-flat surfaces, they need flexible driveshafts. The U-joint compensates for this by allowing it to move up and down with the suspension.
A proper inspection will determine if your u-joints are loose or worn. It should be easy to pull them out. Make sure not to pull them all the way out. Also, the bearing caps should not move. Any signs of roughness or wear would indicate a need for a new UJ. Also, it is important to note that worn UJs cannot be repaired.
Symptoms of Driveshaft Failure
One of the most common problems associated with a faulty driveshaft is difficulty turning the wheels. This severely limits your overall control over the vehicle. Fortunately, there are several symptoms that could indicate that your driveshaft is failing. You should take immediate steps to determine the cause of the problem. One of the most common causes of driveshaft failure is a weak or faulty reverse gear. Other common causes of driveshaft damage include driving too hard, getting stuck in reverse gear and differential lock.
Another sign of a failed driveshaft is unusual noise while driving. These noises are usually the result of wear on the bushings and bearings that support the drive shaft. They can also cause your car to screech or scratch when switching from drive to idle. Depending on the speed, the noise may be accompanied by vibration. When this happens, it’s time to send your vehicle in for a driveshaft replacement.
One of the most common symptoms of driveshaft failure is noticeable jitter when accelerating. This could be a sign of a loose U-joint or worn center bearing. You should thoroughly inspect your car to determine the cause of these sounds and corresponding symptoms. A certified mechanic can help you determine the cause of the noise. A damaged propshaft can severely limit the drivability of the vehicle.
Regular inspection of the drive shaft can prevent serious damage. Depending on the damage, you can replace the driveshaft for anywhere from $500 to $1,000. Depending on the severity of the damage and the level of repair, the cost will depend on the number of parts that need to be replaced. Do not drive with a bad driveshaft as it can cause a serious crash. There are several ways to avoid this problem entirely.
The first symptom to look for is a worn U-joint. If the U-joint comes loose or moves too much when trying to turn the steering wheel, the driveshaft is faulty. If you see visible rust on the bearing cap seals, you can take your car to a mechanic for a thorough inspection. A worn u-joint can also indicate a problem with the transmission.
The cost of replacing the drive shaft
Depending on your state and service center, a driveshaft repair can cost as little as $300 or as high as $2,000, depending on the specifics of your car. Labor costs are usually around $70. Prices for the parts themselves range from $400 to $600. Labor costs also vary by model and vehicle make. Ultimately, the decision to repair or replace the driveshaft will depend on whether you need a quick car repair or a full car repair.
Some cars have two separate driveshafts. One goes to the front and the other goes to the back. If your car has four wheel drive, you will have two. If you’re replacing the axles of an all-wheel-drive car, you’ll need a special part for each axle. Choosing the wrong one can result in more expensive repairs. Before you start shopping, you should know exactly how much it will cost.
Depending on the type of vehicle you own, a driveshaft replacement will cost between PS250 and PS500. Luxury cars can cost as much as PS400. However, for safety and the overall performance of the car, replacing the driveshaft may be a necessary repair. The cost of replacing a driveshaft depends on how long your car has been on the road and how much wear and tear it has experienced. There are some symptoms that indicate a faulty drive shaft and you should take immediate action.
Repairs can be expensive, so it’s best to hire a mechanic with experience in the field. You’ll be spending hundreds of dollars a month, but you’ll have peace of mind knowing the job will be done right. Remember that you may want to ask a friend or family member to help you. Depending on the make and model of your car, replacing the driveshaft is more expensive than replacing the parts and doing it yourself.
If you suspect that your drive shaft is damaged, be sure to fix it as soon as possible. It is not advisable to drive a car with abnormal vibration and sound for a long time. Fortunately, there are some quick ways to fix the problem and avoid costly repairs later. If you’ve noticed the symptoms above, it’s worth getting the job done. There are many signs that your driveshaft may need service, including lack of power or difficulty moving the vehicle.
editor by CX 2023-07-11
China OEM Car Parts Steering Swinging Half Shaft 6r0498099 Outer Rubber CV Boot Joint for VW Polo 1.4 Audi Skoda Se front drive shaft
Product Description
Products Description
Product name | CV Joint (Outer ball joint) |
Size | External Teeth 30, Internal Teeth 27 |
Fitting Position | Front wheel side |
Package Including |
1pc of outer CV Joint 1pc of cv joint grease 1pc of CV boot 2pcs of cv boot clamp |
Application | Suitable for cars after sales service |
Quality guarantee | 1 year |
Leading time | 30 days |
MOQ | 300pcs |
Sample | Avaiable |
Payment way | TT, Trade Assurance on alibaba, PayPal, Western Union |
Advantage | 1. Factory direct wholesale, premium quality and lower price.
2. Most of the items are in stock can be dispatched immediately. |
- AUDI
- A1 (8X1, 8XK) [2571-2018]
- A1 Sportback (8XA, 8XF) [2011-2018]
- SEAT
- IBIZA IV (6J5, 6P1) [2008-]
- IBIZA IV SPORTCOUPE (6J1, 6P5) [2008-]
- IBIZA IV ST (6J8, 6P8) [2571-]
- SKODA
- FABIA II (542) [2006-2014]
- FABIA II Combi (545) [2007-2014]
- FABIA III (NJ3) [2014-]
- FABIA III Estate (NJ5) [2014-]
- VOLKSWAGEN
- POLO (6R1, 6C1) [2009-]
Solve the problem
- Poor comfort
- Over bend tilt
- Abnomal noise
- Driving jitter
- Oil Leaking
Function
- Matching with the size of the original vehicle.
- Improve subversion and eliminate noise.
- Safe,Fixed,Stable,Durable,Quality assurance.
High precision
- Size of the oil seal of the outer ball cage is matching the original vehicle’s ball cage oil seal files.
- Stardard Internal and external splines and thread size easy to install.
- Stardard inner circlip of the inner spline. The stardard width of the circlip makes the movement of the ball cage on the half shaft after loading normally.
- The inner spline rotation is flexible.
- Good quiality materials and exquisite heat treatment performance ensure the product quality.
- Perfect welding:uniform, standard thickness,sureface without crease and good linearity.
Related Products
VW, AUDI, BENZ, BMW, PORSHCHE, LAND ROVER,etc.
1. Clutch system
2. Cooling system
3. Electrical system
4. Transmission system
5. Steering system
6. Drive system
7. Suspension system
8. Braking system
Company Profile
FAQ
1. Is the product fit to your car model?
Please check if the parts are suitable for your model before purchase.
Or please tell us your Car Model and OE Number, and tell us the product name.
2. What you can supply to me?
We could supply all kinds of auto spare parts and accessories. Besides ,we provide OEM service, shipping service and QC service as well to make sure you get ONE-STOP purchase process from us.
3. Can you customize the products as per our request?
Yes, we do OEM and ODM. We could make the product suggestion based on your idea and budget.
4. How to get a sample from you?
All samples will be free if unit cost under 20USD,but the freight should be on your side. If you have express account like DHL,UPS etc we will send you directly, if you don’t have you can send express cost to our paypal account, any sample cost could be returned when you make order.
5. What’s your payment term?
We usually doing 30% deposit and 70% balance against copy of B/L by T/T, We also accept L/C ,D/P if total amount over $30000.
Welcome to your inqury now and built a long cooperatitive relationship with our professional service.
Windy Zhang
Condition: | New |
---|---|
Color: | Silver |
Certification: | ISO, Ts16949 |
Structure: | Single |
Material: | Steel |
Type: | Auto Transmission Systems |
Samples: |
US$ 20/Piece
1 Piece(Min.Order) | |
---|
Customization: |
Available
| Customized Request |
---|
Different parts of the drive shaft
The driveshaft is the flexible rod that transmits torque between the transmission and the differential. The term drive shaft may also refer to a cardan shaft, a transmission shaft or a propeller shaft. Parts of the drive shaft are varied and include:
The driveshaft is a flexible rod that transmits torque from the transmission to the differential
When the driveshaft in your car starts to fail, you should seek professional help as soon as possible to fix the problem. A damaged driveshaft can often be heard. This noise sounds like “tak tak” and is usually more pronounced during sharp turns. However, if you can’t hear the noise while driving, you can check the condition of the car yourself.
The drive shaft is an important part of the automobile transmission system. It transfers torque from the transmission to the differential, which then transfers it to the wheels. The system is complex, but still critical to the proper functioning of the car. It is the flexible rod that connects all other parts of the drivetrain. The driveshaft is the most important part of the drivetrain, and understanding its function will make it easier for you to properly maintain your car.
Driveshafts are used in different vehicles, including front-wheel drive, four-wheel drive, and front-engine rear-wheel drive. Drive shafts are also used in motorcycles, locomotives and ships. Common front-engine, rear-wheel drive vehicle configurations are shown below. The type of tube used depends on the size, speed and strength of the drive shaft.
The output shaft is also supported by the output link, which has two identical supports. The upper part of the drive module supports a large tapered roller bearing, while the opposite flange end is supported by a parallel roller bearing. This ensures that the torque transfer between the differentials is efficient. If you want to learn more about car differentials, read this article.
It is also known as cardan shaft, propeller shaft or drive shaft
A propshaft or propshaft is a mechanical component that transmits rotation or torque from an engine or transmission to the front or rear wheels of a vehicle. Because the axes are not directly connected to each other, it must allow relative motion. Because of its role in propelling the vehicle, it is important to understand the components of the driveshaft. Here are some common types.
Isokinetic Joint: This type of joint guarantees that the output speed is the same as the input speed. To achieve this, it must be mounted back-to-back on a plane that bisects the drive angle. Then mount the two gimbal joints back-to-back and adjust their relative positions so that the velocity changes at one joint are offset by the other joint.
Driveshaft: The driveshaft is the transverse shaft that transmits power to the front wheels. Driveshaft: The driveshaft connects the rear differential to the transmission. The shaft is part of a drive shaft assembly that includes a drive shaft, a slip joint, and a universal joint. This shaft provides rotational torque to the drive shaft.
Dual Cardan Joints: This type of driveshaft uses two cardan joints mounted back-to-back. The center yoke replaces the intermediate shaft. For the duplex universal joint to work properly, the angle between the input shaft and the output shaft must be equal. Once aligned, the two axes will operate as CV joints. An improved version of the dual gimbal is the Thompson coupling, which offers slightly more efficiency at the cost of added complexity.
It transmits torque at different angles between driveline components
A vehicle’s driveline consists of various components that transmit power from the engine to the wheels. This includes axles, propshafts, CV joints and differentials. Together, these components transmit torque at different angles between driveline components. A car’s powertrain can only function properly if all its components work in harmony. Without these components, power from the engine would stop at the transmission, which is not the case with a car.
The CV driveshaft design provides smoother operation at higher operating angles and extends differential and transfer case life. The assembly’s central pivot point intersects the joint angle and transmits smooth rotational power and surface speed through the drivetrain. In some cases, the C.V. “U” connector. Drive shafts are not the best choice because the joint angles of the “U” joints are often substantially unequal and can cause torsional vibration.
Driveshafts also have different names, including driveshafts. A car’s driveshaft transfers torque from the transmission to the differential, which is then distributed to other driveline components. A power take-off (PTO) shaft is similar to a prop shaft. They transmit mechanical power to connected components. They are critical to the performance of any car. If any of these components are damaged, the entire drivetrain will not function properly.
A car’s powertrain can be complex and difficult to maintain. Adding vibration to the drivetrain can cause premature wear and shorten overall life. This driveshaft tip focuses on driveshaft assembly, operation, and maintenance, and how to troubleshoot any problems that may arise. Adding proper solutions to pain points can extend the life of the driveshaft. If you’re in the market for a new or used car, be sure to read this article.
it consists of several parts
“It consists of several parts” is one of seven small prints. This word consists of 10 letters and is one of the hardest words to say. However, it can be explained simply by comparing it to a cow’s kidney. The cocoa bean has several parts, and the inside of the cocoa bean before bursting has distinct lines. This article will discuss the different parts of the cocoa bean and provide a fun way to learn more about the word.
Replacement is expensive
Replacing a car’s driveshaft can be an expensive affair, and it’s not the only part that needs servicing. A damaged drive shaft can also cause other problems. This is why getting estimates from different repair shops is essential. Often, a simple repair is cheaper than replacing the entire unit. Listed below are some tips for saving money when replacing a driveshaft. Listed below are some of the costs associated with repairs:
First, learn how to determine if your vehicle needs a driveshaft replacement. Damaged driveshaft components can cause intermittent or lack of power. Additionally, improperly installed or assembled driveshaft components can cause problems with the daily operation of the car. Whenever you suspect that your car needs a driveshaft repair, seek professional advice. A professional mechanic will have the knowledge and experience needed to properly solve the problem.
Second, know which parts need servicing. Check the u-joint bushing. They should be free of crumbs and not cracked. Also, check the center support bearing. If this part is damaged, the entire drive shaft needs to be replaced. Finally, know which parts to replace. The maintenance cost of the drive shaft is significantly lower than the maintenance cost. Finally, determine if the repaired driveshaft is suitable for your vehicle.
If you suspect your driveshaft needs service, make an appointment with a repair shop as soon as possible. If you are experiencing vibration and rough riding, driveshaft repairs may be the best way to prevent costly repairs in the future. Also, if your car is experiencing unusual noise and vibration, a driveshaft repair may be a quick and easy solution. If you don’t know how to diagnose a problem with your car, you can take it to a mechanic for an appointment and a quote.
editor by CX 2023-06-12
China wholesaler Axle Shaft Used for CZPT OEM42311-60242 Rear Axle Half 40cr Steel 30spline with high quality
Product Description
Product Description
Axle Shaft Used for CZPT 42311-65712
Item Name | Axle Shaft Used for CZPT 42311-65712 |
030Material | 40cr |
HOLE | 6+2 |
splin | 30 |
Accuracy class | JIS B |
MOQ | 100pcs |
length | 793 |
Availability | Can be customized according to drawings |
Warranty | 1years |
Package | Wooden box |
Payment method | T/T,L/C,Western Union,Paypal |
Factory show
Company Profile
Cooperation brand
Our Advantages
FAQ
Q: Which payment terms will you accept?
A: We can accept TT, Western union, paypal and cash etc
Q: When my order will be shipped?
A:Once we get payment, we will ship your order within 20 working days.
Q: Which shipping will you offer?
A:By sea, air, DHL, Fedex, TNT, UPS, EMS, SF
Q: How long does it take to my address?
A:The normal delivery time is 20days, depending on which country you are in.
Q: How can I trace my order?
A:We will send you the tracking number by email.
Q: If I am not satisfied with the products, what should I do?
A:You can contact us and tell us about your problem. We will offer exchange or repair service under warranty.
Material: | 40cr Steel |
---|---|
Load: | Drive Shaft |
Stiffness & Flexibility: | Stiffness / Rigid Axle |
Journal Diameter Dimensional Accuracy: | IT6-IT9 |
Axis Shape: | Straight Shaft |
Shaft Shape: | Real Axis |
Samples: |
US$ 100/Piece
1 Piece(Min.Order) | |
---|
Customization: |
Available
| Customized Request |
---|
How to Replace the Drive Shaft
Several different functions in a vehicle are critical to its functioning, but the driveshaft is probably the part that needs to be understood the most. A damaged or damaged driveshaft can damage many other auto parts. This article will explain how this component works and some of the signs that it may need repair. This article is for the average person who wants to fix their car on their own but may not be familiar with mechanical repairs or even driveshaft mechanics. You can click the link below for more information.
Repair damaged driveshafts
If you own a car, you should know that the driveshaft is an integral part of the vehicle’s driveline. They ensure efficient transmission of power from the engine to the wheels and drive. However, if your driveshaft is damaged or cracked, your vehicle will not function properly. To keep your car safe and running at peak efficiency, you should have it repaired as soon as possible. Here are some simple steps to replace the drive shaft.
First, diagnose the cause of the drive shaft damage. If your car is making unusual noises, the driveshaft may be damaged. This is because worn bushings and bearings support the drive shaft. Therefore, the rotation of the drive shaft is affected. The noise will be squeaks, dings or rattles. Once the problem has been diagnosed, it is time to repair the damaged drive shaft.
Professionals can repair your driveshaft at relatively low cost. Costs vary depending on the type of drive shaft and its condition. Axle repairs can range from $300 to $1,000. Labor is usually only around $200. A simple repair can cost between $150 and $1700. You’ll save hundreds of dollars if you’re able to fix the problem yourself. You may need to spend a few more hours educating yourself about the problem before handing it over to a professional for proper diagnosis and repair.
The cost of repairing a damaged driveshaft varies by model and manufacturer. It can cost as much as $2,000 depending on parts and labor. While labor costs can vary, parts and labor are typically around $70. On average, a damaged driveshaft repair costs between $400 and $600. However, these parts can be more expensive than that. If you don’t want to spend money on unnecessarily expensive repairs, you may need to pay a little more.
Learn how drive shafts work
While a car engine may be one of the most complex components in your vehicle, the driveshaft has an equally important job. The driveshaft transmits the power of the engine to the wheels, turning the wheels and making the vehicle move. Driveshaft torque refers to the force associated with rotational motion. Drive shafts must be able to withstand extreme conditions or they may break. Driveshafts are not designed to bend, so understanding how they work is critical to the proper functioning of the vehicle.
The drive shaft includes many components. The CV connector is one of them. This is the last stop before the wheels spin. CV joints are also known as “doughnut” joints. The CV joint helps balance the load on the driveshaft, the final stop between the engine and the final drive assembly. Finally, the axle is a single rotating shaft that transmits power from the final drive assembly to the wheels.
Different types of drive shafts have different numbers of joints. They transmit torque from the engine to the wheels and must accommodate differences in length and angle. The drive shaft of a front-wheel drive vehicle usually includes a connecting shaft, an inner constant velocity joint and an outer fixed joint. They also have anti-lock system rings and torsional dampers to help them run smoothly. This guide will help you understand the basics of driveshafts and keep your car in good shape.
The CV joint is the heart of the driveshaft, it enables the wheels of the car to move at a constant speed. The connector also helps transmit power efficiently. You can learn more about CV joint driveshafts by looking at the top 3 driveshaft questions
The U-joint on the intermediate shaft may be worn or damaged. Small deviations in these joints can cause slight vibrations and wobble. Over time, these vibrations can wear out drivetrain components, including U-joints and differential seals. Additional wear on the center support bearing is also expected. If your driveshaft is leaking oil, the next step is to check your transmission.
The drive shaft is an important part of the car. They transmit power from the engine to the transmission. They also connect the axles and CV joints. When these components are in good condition, they transmit power to the wheels. If you find them loose or stuck, it can cause the vehicle to bounce. To ensure proper torque transfer, your car needs to stay on the road. While rough roads are normal, bumps and bumps are common.
Common signs of damaged driveshafts
If your vehicle vibrates heavily underneath, you may be dealing with a faulty propshaft. This issue limits your overall control of the vehicle and cannot be ignored. If you hear this noise frequently, the problem may be the cause and should be diagnosed as soon as possible. Here are some common symptoms of a damaged driveshaft. If you experience this noise while driving, you should have your vehicle inspected by a mechanic.
A clanging sound can also be one of the signs of a damaged driveshaft. A ding may be a sign of a faulty U-joint or center bearing. This can also be a symptom of worn center bearings. To keep your vehicle safe and functioning properly, it is best to have your driveshaft inspected by a certified mechanic. This can prevent serious damage to your car.
A worn drive shaft can cause difficulty turning, which can be a major safety issue. Fortunately, there are many ways to tell if your driveshaft needs service. The first thing you can do is check the u-joint itself. If it moves too much or too little in any direction, it probably means your driveshaft is faulty. Also, rust on the bearing cap seals may indicate a faulty drive shaft.
The next time your car rattles, it might be time for a mechanic to check it out. Whether your vehicle has a manual or automatic transmission, the driveshaft plays an important role in your vehicle’s performance. When one or both driveshafts fail, it can make the vehicle unsafe or impossible to drive. Therefore, you should have your car inspected by a mechanic as soon as possible to prevent further problems.
Your vehicle should also be regularly lubricated with grease and chain to prevent corrosion. This will prevent grease from escaping and causing dirt and grease to build up. Another common sign is a dirty driveshaft. Make sure your phone is free of debris and in good condition. Finally, make sure the driveshaft chain and cover are in place. In most cases, if you notice any of these common symptoms, your vehicle’s driveshaft should be replaced.
Other signs of a damaged driveshaft include uneven wheel rotation, difficulty turning the car, and increased drag when trying to turn. A worn U-joint also inhibits the ability of the steering wheel to turn, making it more difficult to turn. Another sign of a faulty driveshaft is the shuddering noise the car makes when accelerating. Vehicles with damaged driveshafts should be inspected as soon as possible to avoid costly repairs.
editor by CX 2023-04-21
China Electric Motor Drive Axle Bus Parts Rear Axle Half Shaft drive shaft assembly parts
Solution Description
The illustration of Rear Axle
Suspension Product |
AR115 |
|
|
Rated load(kg) |
115000 |
Brake Kind |
Disc/Drum |
Rim Length(mm) |
1832 |
Max out Torque(Nm) |
30000 |
Distribution Circle |
ten*335 |
Flange Kind |
Simple Flange |
Ratio |
3.15~6.17 |
Relevant Bus |
7m Bus |
Wheel Hub Variety |
Bearing Unit |
Excess weight(oil included)(kg) |
690()Drum)/630(Disc) |
The Comprehensive Drawing of Described Rear Axle
Variety: Front AXLE—AF two.2~2.7 Sort: Entrance AXLE–AF 5.5
Software: five~7 m Coach/Town Bus Software: ten~11 m Coach/Town Bus
Sort: Front AXLE–AF 75 Kind: REAR AXLE–AR 40
Software: Above eleven m Coach/Town Bus Application: 5~8m Coach/Metropolis Bus
Financial system of The Axle and Suspension
In order to enhance the axle and suspension good quality, increase buyer automobile knowledge, minimize soon after-income routine maintenance fees, entirely discover from domestic and international advanced axle technologies, especially in the axle wheel edge exclusive innovation, from grease lubricated wheel edge, to oil lubricated wheel edge, and then to the maintainance cost-free axle ans suspension wheel edge, in comparison with the previous technology, there is a qualitative leap. Between them, there are 2 sorts of maintenance-cost-free wheel edge: oil lubrication maintenance-free of charge (usually five hundred,000 km upkeep-totally free) and integrated upkeep-totally free (specifically bearing device, 5 many years / 800,000 km maintenance-totally free).
Organization Profile
DUOYUAN Vehicle Products CO.LTD
Duoyuan vehicle gear, addresses an region of much more than a hundred acres and has more than 300 personnel, which includes more than ninety professionals and complex staff, a lot more than 10 senior engineers, and more than thirty intermediate engineers.
Our purpose is to become the third celebration skilled auto components provider with innovative spirit and major engineering. With steady design and development for sixteen years, we have cooperate with YuTong Team for a expression technique. Recent solution market place quantity: Above four hundred,000 items of bus special axles, more than 250,000 kits of bus air suspensions yearly generation potential: one hundred,000 pieces of bus specific axle and fifty,000 kits of bus air suspensions. In 2018, our sales exceeded RMB 1.5 billion.
At current, our items are largely bus-oriented, providing matching items to complete ranges of versions this sort of as passenger bus, vacationer bus, team bus, community transportation bus, school buses and new energy bus Also, we are actively expanding truck and other business automobile marketplaces. Our merchandise are marketed to far more than 130 countries and locations in the globe this kind of as Cuba, Venezuela, Russia, Iran and Saudi Arabia as parts of complete car.
In get to realize a much better potential, we, by upholding the spirit of exploration, learn extensively from others’ sturdy details and soak up foreign and domestic advanced experience, and try for the advancement of China’s automotive equipment.
FAQ
Q:Are you investing firm or manufacturer?
A: We are factory who have been specializing in planning and producing axle and suspension for twenty many years .
Q:Can your merchandise be custom-made or modified?
A: We can design and style and produce the axl and suspension in accordance to customers’ needs and motor vehicle parameters .
Q: What is your phrases of payment ?
A: one hundred% Advance payment by T/T soon after signing the agreement.
Q: What is your conditions of packing?
A: Normally, we put buggy axle on Wood pallets,Stretch movie mounted in picket box . Or Customer necessary.
Q: How prolonged is your supply time?
A: Generally it is fifteen-25 times if the products are in stock. or it is 35-forty five times if the items are not in inventory, it is in accordance to
quantity.
Q: What is your axl sample coverage?
A: We can supply the buggy axle sample if we have completely ready areas in stock, but the clients have to pay out the sample price and he courier expense.Please speak to with me with buggy axle.
Q. Do you take a look at all your buggy axle just before supply?
A: Sure, we have 100% examination just before shipping
Q: How do you make our organization lengthy-expression and very good partnership?
A:1. We keep axle and suspension a good top quality and aggressive price to make certain our buyers advantage
two. We respect each client as our good friend and we sincerely do company and make buddies with them, no subject the place they arrive from.
After-sales Service: | 1 Year |
---|---|
Condition: | New |
Axle Number: | 1 |
Application: | Bus |
Certification: | ISO |
Material: | Steel |
###
Customization: |
Available
|
---|
###
Suspension Model
|
AR115
|
|
|
Rated load(kg)
|
115000
|
Brake Type
|
Disc/Drum
|
Rim Distance(mm)
|
1832
|
Max out Torque(Nm)
|
30000
|
Distribution Circle
|
10*335
|
Flange Type
|
Plain Flange
|
Ratio
|
3.15~6.17
|
Applicable Bus
|
7m Bus
|
Wheel Hub Type
|
Bearing Unit
|
Weight(oil included)(kg)
|
690()Drum)/630(Disc)
|
After-sales Service: | 1 Year |
---|---|
Condition: | New |
Axle Number: | 1 |
Application: | Bus |
Certification: | ISO |
Material: | Steel |
###
Customization: |
Available
|
---|
###
Suspension Model
|
AR115
|
|
|
Rated load(kg)
|
115000
|
Brake Type
|
Disc/Drum
|
Rim Distance(mm)
|
1832
|
Max out Torque(Nm)
|
30000
|
Distribution Circle
|
10*335
|
Flange Type
|
Plain Flange
|
Ratio
|
3.15~6.17
|
Applicable Bus
|
7m Bus
|
Wheel Hub Type
|
Bearing Unit
|
Weight(oil included)(kg)
|
690()Drum)/630(Disc)
|
Different parts of the drive shaft
The driveshaft is the flexible rod that transmits torque between the transmission and the differential. The term drive shaft may also refer to a cardan shaft, a transmission shaft or a propeller shaft. Parts of the drive shaft are varied and include:
The driveshaft is a flexible rod that transmits torque from the transmission to the differential
When the driveshaft in your car starts to fail, you should seek professional help as soon as possible to fix the problem. A damaged driveshaft can often be heard. This noise sounds like “tak tak” and is usually more pronounced during sharp turns. However, if you can’t hear the noise while driving, you can check the condition of the car yourself.
The drive shaft is an important part of the automobile transmission system. It transfers torque from the transmission to the differential, which then transfers it to the wheels. The system is complex, but still critical to the proper functioning of the car. It is the flexible rod that connects all other parts of the drivetrain. The driveshaft is the most important part of the drivetrain, and understanding its function will make it easier for you to properly maintain your car.
Driveshafts are used in different vehicles, including front-wheel drive, four-wheel drive, and front-engine rear-wheel drive. Drive shafts are also used in motorcycles, locomotives and ships. Common front-engine, rear-wheel drive vehicle configurations are shown below. The type of tube used depends on the size, speed and strength of the drive shaft.
The output shaft is also supported by the output link, which has two identical supports. The upper part of the drive module supports a large tapered roller bearing, while the opposite flange end is supported by a parallel roller bearing. This ensures that the torque transfer between the differentials is efficient. If you want to learn more about car differentials, read this article.
It is also known as cardan shaft, propeller shaft or drive shaft
A propshaft or propshaft is a mechanical component that transmits rotation or torque from an engine or transmission to the front or rear wheels of a vehicle. Because the axes are not directly connected to each other, it must allow relative motion. Because of its role in propelling the vehicle, it is important to understand the components of the driveshaft. Here are some common types.
Isokinetic Joint: This type of joint guarantees that the output speed is the same as the input speed. To achieve this, it must be mounted back-to-back on a plane that bisects the drive angle. Then mount the two gimbal joints back-to-back and adjust their relative positions so that the velocity changes at one joint are offset by the other joint.
Driveshaft: The driveshaft is the transverse shaft that transmits power to the front wheels. Driveshaft: The driveshaft connects the rear differential to the transmission. The shaft is part of a drive shaft assembly that includes a drive shaft, a slip joint, and a universal joint. This shaft provides rotational torque to the drive shaft.
Dual Cardan Joints: This type of driveshaft uses two cardan joints mounted back-to-back. The center yoke replaces the intermediate shaft. For the duplex universal joint to work properly, the angle between the input shaft and the output shaft must be equal. Once aligned, the two axes will operate as CV joints. An improved version of the dual gimbal is the Thompson coupling, which offers slightly more efficiency at the cost of added complexity.
It transmits torque at different angles between driveline components
A vehicle’s driveline consists of various components that transmit power from the engine to the wheels. This includes axles, propshafts, CV joints and differentials. Together, these components transmit torque at different angles between driveline components. A car’s powertrain can only function properly if all its components work in harmony. Without these components, power from the engine would stop at the transmission, which is not the case with a car.
The CV driveshaft design provides smoother operation at higher operating angles and extends differential and transfer case life. The assembly’s central pivot point intersects the joint angle and transmits smooth rotational power and surface speed through the drivetrain. In some cases, the C.V. “U” connector. Drive shafts are not the best choice because the joint angles of the “U” joints are often substantially unequal and can cause torsional vibration.
Driveshafts also have different names, including driveshafts. A car’s driveshaft transfers torque from the transmission to the differential, which is then distributed to other driveline components. A power take-off (PTO) shaft is similar to a prop shaft. They transmit mechanical power to connected components. They are critical to the performance of any car. If any of these components are damaged, the entire drivetrain will not function properly.
A car’s powertrain can be complex and difficult to maintain. Adding vibration to the drivetrain can cause premature wear and shorten overall life. This driveshaft tip focuses on driveshaft assembly, operation, and maintenance, and how to troubleshoot any problems that may arise. Adding proper solutions to pain points can extend the life of the driveshaft. If you’re in the market for a new or used car, be sure to read this article.
it consists of several parts
“It consists of several parts” is one of seven small prints. This word consists of 10 letters and is one of the hardest words to say. However, it can be explained simply by comparing it to a cow’s kidney. The cocoa bean has several parts, and the inside of the cocoa bean before bursting has distinct lines. This article will discuss the different parts of the cocoa bean and provide a fun way to learn more about the word.
Replacement is expensive
Replacing a car’s driveshaft can be an expensive affair, and it’s not the only part that needs servicing. A damaged drive shaft can also cause other problems. This is why getting estimates from different repair shops is essential. Often, a simple repair is cheaper than replacing the entire unit. Listed below are some tips for saving money when replacing a driveshaft. Listed below are some of the costs associated with repairs:
First, learn how to determine if your vehicle needs a driveshaft replacement. Damaged driveshaft components can cause intermittent or lack of power. Additionally, improperly installed or assembled driveshaft components can cause problems with the daily operation of the car. Whenever you suspect that your car needs a driveshaft repair, seek professional advice. A professional mechanic will have the knowledge and experience needed to properly solve the problem.
Second, know which parts need servicing. Check the u-joint bushing. They should be free of crumbs and not cracked. Also, check the center support bearing. If this part is damaged, the entire drive shaft needs to be replaced. Finally, know which parts to replace. The maintenance cost of the drive shaft is significantly lower than the maintenance cost. Finally, determine if the repaired driveshaft is suitable for your vehicle.
If you suspect your driveshaft needs service, make an appointment with a repair shop as soon as possible. If you are experiencing vibration and rough riding, driveshaft repairs may be the best way to prevent costly repairs in the future. Also, if your car is experiencing unusual noise and vibration, a driveshaft repair may be a quick and easy solution. If you don’t know how to diagnose a problem with your car, you can take it to a mechanic for an appointment and a quote.
editor by czh 2022-12-03
China Best Sales 2403511-P301-GC rear axle half axle for CZPT 700p 4hk1 drive shaft rear wheel shaft axle with Best Sales
Model: ASCENDER
Calendar year: 2003-2006
Vehicle Fitment: ISUZU
Product Quantity: 245711-P301-GC
Vehicle Make: CZPT 700p 4hk1
OE NO.: 245711-P301-GC
Guarantee: twelve Months
Length: 34.84(in)/885mm
Spline: twenty
HOLES: 8+one
Packaging Information: Frim packing
Port: HangZhou
Merchandise record 245711-P301-GC rear axle fifty percent axle for CZPT 700p 4hk1 push shaft rear wheel shaft axle
Because there are as well a lot of designs, oxide black Cast Steel or Stainless steel Flat Belt loafer Pulleys the desk can’t show them all. Make sure you seek advice from on the internet client service.Thank you
NO.
Oem
Modle
Length/mm
Splines
Holes
1
42311-26300
TOYOTA HAICE KDH211 RH
825
thirty
6+1
2
42311-26290
TOYOTA HAICE KDH20# RH
733
30
6+1
3
42311-26301
TOYOTA HAICE 2005 Narrow 1695 DIESEL
825
thirty
6+1
4
42311-0K040
TOYOTA HILUX 7 Vigo 2005-2015 KUN26
764
thirty
6+1
5
42311-0K030
TOYOTA HILUX KUN25 RH
764
30
6+1
6
42311-0K070
TOYOTA HILUX KUN16 RH/HILUX DLX 5LE 2005-2013
764
thirty
5+1
7
42311-0K090
TOYOTA HILUX KUN26 LHD RH
764
thirty
6+1
8
42311-35330
TOYOTA HILUX/4RUNNER TRUCK
663
30
6+1
9
42311-35140
TOYOTA HILUX 4 1983-1988/HILUX 5 1988-1997
663
thirty
6+1
ten
42311-KK040
770
32
6+2
11
42311-65710
TOYOTA Landcruiser
783
thirty
6+2
12
42311-65712
TOYOTA Landcruiser
783
30
6+2
13
42312-60070
TOYOTA Landcruiser
824
thirty
6+1
14
3W1Z-4234-A
Ford
860
28
5
15
6W1Z-4234-A
Ford
860
31
5
sixteen
F8AZ-4234-A
Ford
809
28
5
seventeen
42311-14990
990
39
10
eighteen
MB35711
MITSUBISHI
770
eighteen
8+2
19
MB35713
MITSUBISHI
800
18
8+2
twenty
MC881679
MITSUBISHI
950
20
8
21
MK499638/MC864169
MITSUBISHI/Canter lntercooler FE74/seventy five, Heavy duty Aluminum sliding window wheel doorway roller pulley manufacturing facility price tag effortlessly sliding window pulley Nylon single Bearing Colt Diesel FE349/120PS
802/805
18
8+2
22
MK499638-M/MC864169-M
MITSUBISHI/Canter lntercooler FE74/seventy five, Substantial good quality Italian manufacturer RD 210 rotary tiller lateral agricoltural equipment electricity gearbox tractors cultivators Colt Diesel FE349/120PS
805
18
8+2
23
ME508085
Canter lntercooler FE75 SHDX/H-Equipment
805
18
8+2
24
42311-0W030 /42311-LAA30
TOYOTA
774.5
37
8+2+2
twenty five
3162-2403070-01
patriot Jeep
874
ten
10+2
26
42311-36210
COASTER
770/776
34
6+2+2
27
42311-37140
Hino three hundred
865
37
10
Manual to Push Shafts and U-Joints
If you happen to be anxious about the efficiency of your car’s driveshaft, you happen to be not by itself. Numerous vehicle proprietors are unaware of the warning signs of a failed driveshaft, but realizing what to look for can assist you stay away from expensive repairs. Right here is a transient manual on push shafts, U-joints and upkeep intervals. Outlined below are essential factors to take into account ahead of replacing a motor vehicle driveshaft.
Signs and symptoms of Driveshaft Failure
Determining a defective driveshaft is simple if you’ve at any time heard a strange noise from underneath your automobile. These seems are induced by worn U-joints and bearings supporting the travel shaft. When they fail, the push shafts stop rotating appropriately, generating a clanking or squeaking audio. When this transpires, you might hear sounds from the facet of the steering wheel or floor.
In addition to noise, a defective driveshaft can lead to your car to swerve in restricted corners. It can also direct to suspended bindings that restrict overall management. For that reason, you need to have these signs checked by a mechanic as quickly as you observe them. If you recognize any of the symptoms over, your next step ought to be to tow your vehicle to a mechanic. To stay away from additional problems, make certain you’ve taken safety measures by checking your car’s oil amount.
In addition to these signs and symptoms, you ought to also appear for any noise from the push shaft. The first factor to appear for is the squeak. This was induced by severe harm to the U-joint attached to the travel shaft. In addition to sound, you must also seem for rust on the bearing cap seals. In extreme situations, your auto can even shudder when accelerating.
Vibration although driving can be an early warning sign of a driveshaft failure. Vibration can be thanks to worn bushings, trapped sliding yokes, or even springs or bent yokes. Extreme torque can be induced by a worn heart bearing or a broken U-joint. The motor vehicle may possibly make unusual noises in the chassis method.
If you observe these signs, it is time to get your vehicle to a mechanic. You must check out often, particularly weighty cars. If you’re not certain what is actually causing the noise, check out your car’s transmission, engine, and rear differential. If you suspect that a driveshaft needs to be replaced, a accredited mechanic can replace the driveshaft in your vehicle.
Travel shaft variety
Driveshafts are employed in numerous distinct sorts of automobiles. These incorporate four-wheel generate, front-motor rear-wheel push, bikes and boats. Each kind of drive shaft has its personal goal. Below is an overview of the a few most frequent types of drive shafts:
The driveshaft is a round, elongated shaft that transmits torque from the motor to the wheels. Travel shafts frequently have many joints to compensate for changes in length or angle. Some push shafts also include connecting shafts and interior continual velocity joints. Some also incorporate torsional dampers, spline joints, and even prismatic joints. The most important issue about the driveshaft is that it performs a important role in transmitting torque from the engine to the wheels.
The generate shaft wants to be both light and powerful to shift torque. Even though steel is the most generally utilized materials for automotive driveshafts, other resources these kinds of as aluminum, composites, and carbon fiber are also frequently utilized. It all is dependent on the goal and dimensions of the automobile. Precision Producing is a great supply for OEM items and OEM driveshafts. So when you might be searching for a new driveshaft, hold these elements in brain when purchasing.
Cardan joints are another common drive shaft. A common joint, also recognized as a U-joint, is a flexible coupling that makes it possible for one particular shaft to generate the other at an angle. This kind of generate shaft allows electrical power to be transmitted although the angle of the other shaft is constantly modifying. Whilst a gimbal is a very good choice, it really is not a perfect remedy for all applications.
CZPT, Inc. has condition-of-the-art machinery to services all varieties of drive shafts, from tiny autos to race automobiles. They provide a range of demands, including racing, business and agriculture. No matter whether you need to have a new generate shaft or a straightforward adjustment, the staff at CZPT can satisfy all your wants. You will be back on the highway quickly!
U-joint
If your car yoke or u-joint shows indications of wear, it really is time to change them. The easiest way to replace them is to stick to the actions underneath. Use a large flathead screwdriver to check. If you feel any movement, the U-joint is faulty. Also, inspect the bearing caps for injury or rust. If you are unable to discover the u-joint wrench, attempt checking with a flashlight.
When inspecting U-joints, make confident they are effectively lubricated and lubricated. If the joint is dry or inadequately lubricated, it can speedily fall short and result in your auto to squeak while driving. An additional sign that a joint is about to fall short is a sudden, too much whine. Check your u-joints each calendar year or so to make positive they are in appropriate operating buy.
No matter whether your u-joint is sealed or lubricated will rely on the make and model of your vehicle. When your car is off-highway, you want to put in lubricable U-joints for longevity and longevity. A new driveshaft or derailleur will expense a lot more than a U-joint. Also, if you never have a very good knowing of how to replace them, you may require to do some transmission perform on your motor vehicle.
When replacing the U-joint on the travel shaft, be confident to decide on an OEM replacement each time possible. Although you can simply mend or substitute the original head, if the u-joint is not lubricated, you may want to substitute it. A damaged gimbal joint can result in issues with your car’s transmission or other essential parts. Replacing your car’s U-joint early can guarantee its long-time period efficiency.
An additional option is to use two CV joints on the push shaft. Utilizing numerous CV joints on the travel shaft will help you in conditions in which alignment is difficult or functioning angles do not match. This sort of driveshaft joint is a lot more high-priced and intricate than a U-joint. The down sides of employing a number of CV joints are further size, excess weight, and reduced functioning angle. There are many reasons to use a U-joint on a push shaft.
routine maintenance interval
Examining U-joints and slip joints is a critical part of routine upkeep. Most vehicles are equipped with lube fittings on the driveshaft slip joint, which must be checked and lubricated at each and every oil modify. CZPT professionals are nicely-versed in axles and can effortlessly identify a undesirable U-joint based mostly on the sound of acceleration or shifting. If not repaired effectively, the push shaft can drop off, necessitating costly repairs.
Oil filters and oil adjustments are other components of a vehicle’s mechanical system. To prevent rust, the oil in these elements have to be replaced. The identical goes for transmission. Your vehicle’s driveshaft need to be inspected at the very least every 60,000 miles. The vehicle’s transmission and clutch need to also be checked for dress in. Other components that need to be checked include PCV valves, oil traces and connections, spark plugs, tire bearings, steering gearboxes and brakes.
If your automobile has a handbook transmission, it is best to have it serviced by CZPT’s East Lexington professionals. These services need to be executed each and every two to four a long time or every 24,000 miles. For best outcomes, refer to the owner’s guide for recommended routine maintenance intervals. CZPT technicians are knowledgeable in axles and differentials. Standard upkeep of your drivetrain will preserve it in excellent functioning buy.